使用規則 OPERATION INSTRUCTIONS
使用前須查機件完好無損.傳動部分及起重鏈條潤滑良好。 空轉情況正常,制動可靠。使用時必須嚴守下面10條安全事項。
Before lifting, inspect carefully the hooks,the load chain.the brake device and iubrication of the block,put it into operation.
For safe operation you must keep rules as following.
維 護 Maintenance
1、使用完畢應將葫蘆清理干凈并涂上防銹油脂,存放在干燥地方。
Chean off the dirt on the chain hoist.lubricate its parts with grease
Atrer use and store it in a dry place.
2、 維護和檢修應由較熟練葫蘆機械者進行,防止不懂本機性能原理隨意拆裝。
Maintenance and inspection should bo maae by ask- illed
3、 齒輪的安裝如右剖視圖所示位量,應使用兩只片齒輪的 “0”字標記安裝在同一直線上。
Align the "oMmarks of the two gears while assembling as shown in SectionView RiGHT.
4、 安裝制動裝置部分時,注意棘輪齒槽與棘爪爪部嚙合良好,彈簧和棘爪應錄活可靠.順時針旋轉手鏈輪,應將棘輪、摩擦片壓緊在制動器座上,逆時針旋轉手鏈輪,棘輪與磨擦片間應留有空隙。
While assembling the brake mechanism.care should be taken to mesh the slanting teeth of the ratchet disc and the pawl. Make sure that the spring and pawl work sensitively and reliably. Tnen turn the hand wheel clockwise.it must prees the disc and the plates on the brake seat .Tumiyng it counter-clockwise.there should be clearances between the disc and the plates.
5、 葫蘆經過清洗檢修應進行空載和載重試驗.確認工作正常.制動可靠時,才能交付使用。
After cleaning and repairing the hoist should be subjec-ted to no-load sest and heavy load test. A chain'hoist can be put into operation a rter it has been tested and found under reliable brake and in good condition.
6、 在加油和使用過程中制動器的摩擦表面必須保持干凈, 制動器部分應當經常檢查.防止制動失靈,發生重物自墜現象。
Keep Icean the friction sursaces of the brade.Brake mech-anism shoula be inspected regularly for prevention of faulty braking and falling of the load.
7、 起重鏈輪左右軸承的滾柱,可用黃油粘附在已壓裝于起 重鏈輪軸頸的軸承內圈上,再入墻板軸承外圈內。
Stick the rollers of both left and right bearings to the ynner race of the bearing on the chain sprocket shaft journal,and then put them into the outter race of the bearings on the side plates.
8、 支撐桿與右墻板為靜配合,維修時切勿拆卸。
The stay and the right side are in transition fit.Care should be taken not to dismantle them.
9、 為了維護和拆卸方便,手鏈條其中一節系開口鏈 (不焊,涂色)。
For conveniense of maintenance and dismantling,one of the links of the hand chain is open,painted in color and . not welded.
HSZ型系列手拉葫蘆性能參數表 HSZ SERIES CHAIN BLOCKS
hsz型系列拉葫蘆是一種使用廣泛,攜帶方便的手動起重機械.可用于工業農業、速筑業、礦業礦業等的機械安裝:、貨物起吊、車輛裝卸等,尤其適用于露天及無電源作業。
HSZ手拉葫蘆與各型手拉單軌行車配套使用組成手拉起重運輸小車,適用于單軌架空運輸,手動以單梁橋式起重機和懸臂式起重機上.
型號 Model | hsz-V2 | HSZ-1 | HSZ-1,l2 | HSZ-2 | HSZ-3 | HSZ- 5 | HSZ-10 | HS2-20 | |
起重里 Capacity 噸t | 0.5 | 1 | 1.5 | 2 | 3 | 5 | 10 | 20 | |
標準起第高度 Standard lifting height m 米 | 2.5 | 2.5 | 7 B | 2. 5 | 3 | 3 | 3 | 3 | |
試驗軟荷 Test load 噸t | 0.63 | 1.25 | 2 | 2.5 | 4 | 6.3 | 12. 5 | 25 | |
兩鉤間小距離 _ Hmin heardroom(hook to book)Hnin | 270 | 270 | 368 | 444 | 486 | 616 | 700 | 1000 | |
滿載時手鏈拉力 Chainpull to lift full load牛賴N | 225 | 309 | 343 | 314 | 343 | 383 | 392 | 392 | |
起重鏈行數 No.of load chain fall lines | 1 | 1 | 1 | 2 | 2 | 2 | 4 | 8 | |
起重鏈條圓鋼直徑 Diameter of load chain毫米mm | 6 | 6 | 8 | 6 | 8 | 10 | 10 | 10 | |
主要尺寸Diaroensions 毫米mm | A | 120 | 142 | 178 | 142 | 178 | 210 | 358 | 580 |
B | 108 | 122 | 139 | 122 | 139 | 182 | 162 | 189 | |
C | 24 | 28 | 34 | 34 | 38 | 48 | 64 | 82 | |
D | 120 | 142 | 178 | 142 | 178 | 210 | 210 | 210 | |
凈重 Net weight 公斤Kk | 9.5 | 10 | 16 | 14 | 24 | 36 | 68 | 155 | |
裝箱毛重 Gross Weight 公斤KK | 12 | 13 | 20 | 17 | 28 | 45 | 83 | 193 | |
裝箱尺寸(長X寬X高〉 面#、 Packing measurement (L*W*H) | 28X21X17 | 30X24X18 | 34X29X20 | 33X25X19 | 38X30X20 | 45X35X24 | 62X50X28 | 70X46X75 | |
起重高度每增加1米應增加的重f /Vff . Extra weight meter of extra lift | 1.7 | 1.7 | 2.3 | 2. 5 | 3.7 | 5.3 | 9 7 | 19.4 |
注:除表列外.在丨2 米以內各起® 高度.均可定貨.R«n«rki:lnaddtiiMi to th« standard lift «t sccept in^ilnt orders to 12n lift.
HSZ型手拉葫蘆備件明細錄
DETAILS OF SPARE PARTS FOR HSZ SERIES CHAIN BLOCKS
1.起重鏈 | 11.摩擦片 | 21.左墻板 | 31.外墻板 |
2.右墻板 | 12.滾柱 | 22.吊鏈板 | 32.滾柱 |
3.支撐桿甲 | 13、軸承外圈 | 23.吊銷 | 33.罩殼 |
4.起重鏈輪 | 14.棘輪 | 24.擋板 | 34.游輪軸 |
5.5齒長軸 | 15.手鏈輪 | 25.彈性擋圈 | 35.滾針 |
6.花鍵孔齒輪 | 16.棘爪彈簧 | 26.插銷 | 36.游輪 |
7.4齒短軸 | 17.棘爪 | 27.導輪 | 37.吊鉤梁 |
8.片齒輪 | 18.手鏈輪罩殼 | 28.鋼套 | 38.吊鉤 |
9.手鏈輪 | 19.彈性擋圈 | 29.支撐桿乙 | 39.卡索板 |
10.制動器座 | 20.棘爪銷 | 30.下鉤架 | 40.雙彈簧 |